The 6346 Complete PakPress® Kit is a must if you’re in the Fleet Maintenance industry.  Don’t be without this tool that brings the power of a 10-ton shop press right to the truck.  Most impressive, the PakPress® lets you remove and install studs without removing the hub. A two-hour job is done in twenty minutes, with no risk of damaging seals or bearings.

The 6346 Complete PakPress® Kit includes:

• 1-PPK PakPress®
• 6247 PakPress® Cart
• Adapters ( 6261,6235, 6236, 6361)

The HD-22 Clever Lever® puts science back in this chore by providing just the right tool to remove and replace tires easily and safely. The Clever Lever® allows one person to easily move tires up to 300 lbs., helping to prevent back injuries and other costly insurance claims. Simply roll the Clever Lever® under the tire, then lift and pull. To replace a tire, simply push it back in, rotate and tilt for quick alignment with the studs. The Clever Lever® comes in two models that fit everything from light/medium duty pickups to heavy-duty tractors and trailers. The HD-22 Clever Lever® fits tires from 24″ to 36 “.

For larger tires the HD-26 Clever Lever® is available and fits tires 36″ to 48″.

Actual Weight
19 lbs
Shipping Weight
31 lbs

Replacement frame with cylinder and adapters
(does not include hoses or pump)

The 1-PPK PakPress® Portable Wheel Stud Remover and Installer is a must if you’re in the Fleet Maintenance industry. Don’t be without this tool that brings the power of a 10-ton shop press right to the truck. Most impressive, the 1-PPK PakPress®  lets you remove studs safely without damage. A two-hour job is done in twenty minutes, with no risk of damaging seals or bearings. Any mechanic can use it and get the job done right in minutes.

The TW2000 Tweel Handler™ is an amazingly versatile tool that allows truck mechanics to remove, install, rotate and transport single tire-and-wheel assemblies with ease. The vertical range of conventional wheel dollies is 3″ or 4″, forcing you to kneel down to inspect tires, or use a floor jack to raise the tire up. The TW2000 solution is a built-in ratcheting jack with 14″ of vertical travel. No more bending over! The Tweel Handler’s U-shaped chassis allows you to get close to the work area, with unhindered access to the tire in the cradle. No restraining chains are required, yet the Tweel Handler™ holds virtually any single truck wheel, including wide-based singles. Three heavy-duty ball-bearing wheels mounted under ball-bearing swivel casters make it highly maneuverable.

Minimum Tire/Wheel Diameter:  23.5″
Maximum Tire/Wheel Weight:  350 lbs
Cradle Depth:  14″
Cradle Width:  23.5″
Supporting Ring Roller Spread:  37″
Vertical Hoist Travel:  14″

The VV 3000 Versa Vac™ Radiator Pressure Tester and Coolant Dam will pay for itself after just a few uses. Ingenious and simple, this new time saving tool holds the engine coolant in, even when pipe plugs, sensors or valves are removed for replacement or repair. The Versa-Vac™ Pressure Tester creates a vacuum, holding coolant in with little or no loss. For many minor repairs, there is no need to spend valuable shop time draining and refilling the system. The Versa-Vac™ unit fits standard radiator necks and installs as quickly as a radiator cap.  Adapters are available to fit special applications. As a pressure tester, the Versa-Vac™ allows a quick check of your repair with positive pressure from shop air.  No tedious hand pumping.  A radiator cap installs on the tester to provide pressure relief. An inlet ball valve adjusts the pressure applied to the system up to the maximum limit of the relief valve.

Air requirement for continuous use: approximately 30 CFM at 120-150 PSI.

*** ADAPTERS REQUIRED AND SOLD SEPARATELY ***