CH-22 Manual Tire Changer

The VV 3000 Versa Vac™ Radiator Pressure Tester and Coolant Dam will pay for itself after just a few uses. Ingenious and simple, this new time saving tool holds the engine coolant in, even when pipe plugs, sensors or valves are removed for replacement or repair. The Versa-Vac™ Pressure Tester creates a vacuum, holding coolant in with little or no loss. For many minor repairs, there is no need to spend valuable shop time draining and refilling the system. The Versa-Vac™ unit fits standard radiator necks and installs as quickly as a radiator cap.  Adapters are available to fit special applications. As a pressure tester, the Versa-Vac™ allows a quick check of your repair with positive pressure from shop air.  No tedious hand pumping.  A radiator cap installs on the tester to provide pressure relief. An inlet ball valve adjusts the pressure applied to the system up to the maximum limit of the relief valve.

Air requirement for continuous use: approximately 30 CFM at 120-150 PSI.

*** ADAPTERS REQUIRED AND SOLD SEPARATELY ***

The 1-PPK PakPress® Portable Wheel Stud Remover and Installer is a must if you’re in the Fleet Maintenance industry. Don’t be without this tool that brings the power of a 10-ton shop press right to the truck. Most impressive, the 1-PPK PakPress®  lets you remove studs safely without damage. A two-hour job is done in twenty minutes, with no risk of damaging seals or bearings. Any mechanic can use it and get the job done right in minutes.

The HD-22 Clever Lever® puts science back in this chore by providing just the right tool to remove and replace tires easily and safely. The Clever Lever® allows one person to easily move tires up to 300 lbs., helping to prevent back injuries and other costly insurance claims. Simply roll the Clever Lever® under the tire, then lift and pull. To replace a tire, simply push it back in, rotate and tilt for quick alignment with the studs. The Clever Lever® comes in two models that fit everything from light/medium duty pickups to heavy-duty tractors and trailers. The HD-22 Clever Lever® fits tires from 24″ to 36 “.

For larger tires the HD-26 Clever Lever® is available and fits tires 36″ to 48″.

Actual Weight
19 lbs
Shipping Weight
31 lbs

The TW2000 Tweel Handler™ is an amazingly versatile tool that allows truck mechanics to remove, install, rotate and transport single tire-and-wheel assemblies with ease. The vertical range of conventional wheel dollies is 3″ or 4″, forcing you to kneel down to inspect tires, or use a floor jack to raise the tire up. The TW2000 solution is a built-in ratcheting jack with 14″ of vertical travel. No more bending over! The Tweel Handler’s U-shaped chassis allows you to get close to the work area, with unhindered access to the tire in the cradle. No restraining chains are required, yet the Tweel Handler™ holds virtually any single truck wheel, including wide-based singles. Three heavy-duty ball-bearing wheels mounted under ball-bearing swivel casters make it highly maneuverable.

Minimum Tire/Wheel Diameter:  23.5″
Maximum Tire/Wheel Weight:  350 lbs
Cradle Depth:  14″
Cradle Width:  23.5″
Supporting Ring Roller Spread:  37″
Vertical Hoist Travel:  14″

The SU100A Stepper™ gives you safe and secure footing while you work on truck engines. This convenient tool goes over the front or rear tire of the vehicle to give you easier access to hard-to-reach places. It’s adjustable for most tire sizes and folds flat for convenient transport and storage.

The 350B Back Buddy II™ will make brake jobs easier and more profitable. This versatile tool was designed to prevent injuries from awkward lifting and keep workers’ comp rates down. The Back Buddy II™ rolls under and bolts onto heavy drum and hub assembly, then handily rolls the assembly out and lays it over for servicing. Re-assembly is quick and precise because the Back Buddy II™ angles for perfect hub alignment, eliminating seal damage and costly fixes. The Back Buddy II™ handles all hub and drum assemblies with Universal Receiver and Adapter Sets. A simple change of adapters transforms the tool in seconds from inboard to outboard application.

*Adapters 6069 and 6073 10-hole inboard and outboard application are included
*Other wheel adapters sold separately.